Note (page 2 / 3)

Conductivity of hose should be tested regularly. Test with OHMS meter using conductive fittings inserted into each end of hose.

Contact Anderson Process for attachment procedure and other coupling recommendations.

Contact Anderson Process for proper fitting recommendation and coupling procedure.

Contact Anderson Process for proper fitting recommendation and coupling procedure. Coupled lengths with MxMS fittings and Kink Guards available.

Contact Anderson Process for proper fitting recommendation and coupling procedures.

Contacts Not Included

Contacts Not Included; Insert Not Included

Contacts Not Included; Insert Only, Requires Shell

Contacts Not Included; Jam Nut Not Included

Custom models, larger sizes and higher pressure ratings available on request

Custom models, larger sizes and higher pressure ratings available on request.

DIN Dash Size = 06

DIN Dash Size = 10

DIN Dash Size = 12

Designed with 304 stainless steel band, bolt and nut.

Designed with Cavity Filler

Diverter includes trim and rough in valve

Does not contain adhesive

Electrical Resistivity: 100 gigaohms per foot at 1000 volts DC or better

Electrical Resistivity: 50 gigaohms per foot at 1000 volts DC

Electrical resistivity: Greater than 1000 gigaothms at 1000 volts DC

Equipped with stainless steel mounting legs

Evaluation, Development board not included with enclosure.

FOR APPLICATIONS INVOLVING INDUSTRIAL ACID CHEMICALS AND ALCOHOLS, PLEASE REFER TO T505OG AND T509OE CHEMICAL HOSES

For Coalescing Units

For End Surface Groove Machining, PR930: For Low-speed Machining of Steel/Stainless Steel

For Parting Machining, PR1535: Stainless Steel Parting Machining (First Recommended Material)

For VISI-FLO 1400 Series Sight Flow Indicator

For VISI-FLO 1500 Series Sight Flow Indicator

For higher pressure applications, consult factory. Units equipped with differential pressure indicator have max. temperature and pressure of 125?F and 150 PSIG, regardless of bowl material.

For higher pressure stainless steel applications, please consult factory.

For higher pressure units, consult factory.

For turning, CA510: High-speed/high-efficiency steel machining

For turning, CA530: Supports general to heavy intermittent machining of steel (focus on stability)

For turning, PV720: the foremost recommended PVD cermet for steel machining

For turning, TN620: the foremost recommended cermet for steel machining

For use with 150lb. floating flange.

For use with Campbell Cobra Parts C & E and Standard Cobra Parts C & E.

For use with combination nipples, suction hose couplings and ball & socket couplings.

For use with crimpnology nipples, Campbell Cobra Parts C & E, ChemJoint couplings & male stems and sanitary tri-clamp.

For use with long crimpnology nipples, viton seal ground joints and male stems.

For use with sleeves or bands.

G: High Tensile Galvanized Carbon Steel Inner/Outer Helix

GYLON? is a registered trademark of Garlock.

Grounding Lug included

High durability

Hose assemblies are furnished with the following fittings: 1/4" ID ? 1/4" X 1/4"M NPT, 3/8" ID ? 3/8" X 1/4"M NPT, 1/2" ID ? 1/2" X 3/8"M NPT.

Hose assemblies are furnished with the following fittings: 1/4" ID ? 1/4" X 1/4"M NPT, 3/8" ID ? 3/8" X 1/4"M NPT.

Hose may be sterilized with 5% soda solution.

Hot water at 175?F at 5 psid for 30 minutes; In-line steam at 257?F @ 1 psid for 30 minutes; Autoclavable at 257?F for 30 minutes; 5.6 sq. ft. per 10 in. in length

Hot water at 175?F at 5 psid for 30 minutes; In-line steam at 257?F @ 1 psid for 30 minutes; Autoclavable at 257?F for 30 minutes; 6.0 sq. ft. per 10 in. filter length

Hot water at 175?F at 5 psid for 30 minutes; In-line steam at 257?F @ 1 psid for 30 minutes; Autoclavable at 257?F for 30 minutes; 7.0 sq. ft. per 10 in. in length

Hot water at 175?F at 5 psid for 30 minutes; In-line steam at 257?F @ 1 psid for 30 minutes; Autoclavable at 257?F for 30 minutes; 7.2 sq. ft. per 10 in. filter length

Hot water at 175?F at 5 psid for 30 minutes; In-line steam at 257?F @ 1 psid for 30 minutes; Autoclavable at 257?F for 30 minutes; 8.5 sq. ft. per 10 in. filter length

Hot water at 194?F @ max 3 psid for 30 minutes; In-line steam at 257?F @ max 3 psid for 30 minutes; Autoclavable at 257?F for 30 minutes

IEC61672 replaces 2 obsolete standards, IEC60651 andIEC60804

Image is for reference ONLY. Actual liner may vary in size, shape, and/or color depending on your selection..

Impellers are full size diameter - If trimming is needed please contact Anderson Process.

Includes KOPkit, Bleed Valve, Injection Valve, Foot Valve Strainer, Tubing

Includes Mounting Legs

Includes O-Rings and Retaining Ring

Includes Safety Clip

Includes Sanitary Twist Valve Kit

Includes mounting bracket kit and rod (for opening & closing)

Interlocking Bolt Clamps recommended when assembling to a hose.

Kit Includes - Impeller, Impeller Key, Impeller Nut, Stub Shaft, Shaft Collar, Impeller Nut Gasket, Impeller Back Gasket

Kit Includes - Mechanical Seal, Casing Gasket, Impeller Nut Gaskets (2).

Kit Includes - Mechanical Seal, Casing Gasket, Impeller O-Ring.

Kit Includes - Mechanical Seal, Casing Gasket, Impeller Screw O-Ring/Gasket, Shaft Sleeve O-Ring(s).

Kit Includes - Mechanical Seal, Casing Gasket, O-Ring Between Sleeve & Impeller, Impeller Screw O-Ring.

Kit Includes - O-Ring for Rotor (2), Rotor Case (2), Rotor Bolt (2), Front Cover (1), Mechanical Seal Ring (4), Mechanical Seal Base (2), DIN M6 Fender Washer (4-6), Cap Screw for Retainer (4-6).

Kit Includes - O-Ring for Rotor (2), Rotor Case (2), Rotor Bolt (2), Front Cover (1), Sleeve (2).

Kit Includes - Seal Carbon, Seal O-Ring, Spring "D" Seal, Cup "D"

LGV has capabilities of customizing product to thicker material or making fitting a jump size. MADE IN USA.

Low creep and cold flow

Made in the U.S.A.

Made in the USA

Max W.P. @ 68?F - Working pressure (W.P.) is temperature dependent

Metal Detectable/X-ray Inspectable

Minimum batch size is one gallon. Batch sizes less than one gallon may compromise system accuracy.

Most standard bimetal thermometer options are available with Sanitary Tri-Clamp connection, consult factory.

Motor Drive: 110V & 220V Single Phase, Pneumatic

Motor Drive: 110V & 220V Single Phase, Pneumatic, Explosion Proof

NON-RETURNABLE / VARIABLE LEADTIME

No Cavity Filler

No aging or hardening in service

Non-aging in service

Non-contaminating, non-particulating

Non-toxic, silicone-free

First Prev 1 2 3 Next Last